简要说明：怎样对链板式输送机进行保养？产品：估价：1，规格：完善，产品系列编号：齐全

怎样对链板式输送机进行保养？下面就是详细内容。

How the chain plate conveyor www.rzxtdbw.com maintenance? The following is the details.

a.链轮装在轴上应没有歪斜和摆动。在同一传动组件中两个链轮的端面应位于同一平面内，链轮中心距在0.5米以下时，允许偏差１毫米；链轮中心距在0.5米以上的时，允许偏差2毫米。

A. sprocket mounted on a shaft should not skewed and swing. The two sprockets face in the same transmission components should be www.aiyiyangsheng.com located on the same plane, the sprocket center distance of 0.5 m, allowable deviation of 1 mm; The sprocket center distance of 0.5 m above, the allowable deviation of 2 mm.

b.链条的松紧度应适宜，太紧增加功率消耗，轴承易磨损；太松链条易跳动和脱链。链条的松紧程度为：从链条的中部提起或压下，两链轮中心距的约为2％－3％。

B. chain looseness should be appropriate, increase power consumption is too tight, bearing wear easily; Too loose chain easy to beat and take www.wlxinhua.com off the chain. Tightness of the chain is: filed or under pressure from the central part of the chain, two chain wheel center distance of about 2% to 2%.

c.新链条过长或经使用后伸长，难以调整，可看情况拆去链节，但必须为偶数。链节应从链条背面穿过，锁片插在外面，锁紧片的开口应朝转动的相反方向。

C. new chain is too long or elongation after use, it is difficult to adjust, can see things down link, but must be even. Through the link from the chain www.wlxinhua.com on  the back of the lock plate inserted in the outside, lock piece of opening should be toward the rotation in the opposite direction.

d.链轮磨损严重后，应同时更换新链轮和新链条，以保证良好的啮合。不能只单独更换新链条或新链轮。否则会造成啮合不好加速新链条或新链轮的磨损。链轮齿面磨损到一定程度后应及时翻面使用。以延长使用时间。

D. after the sprocket wheel wear serious, should replace the new sprocket and chain at the same time, to ensure good mesh. Can not only replace new sprocket chain or separately. Otherwise it will cause bad meshing accelerate new chain or chain wheel wear. Sprocket tooth surface wear to a certain degree to flip timely after use. For prolonged use.

e.旧链条上不能与部分新链条混合使用，否则容易在传动中产生冲击，拉断链条。

E. the old chain cannot be used mixed with part of the new chain, otherwise easy to impact in the transmission, break the chain.

f.链板式输送机上的链条在工作中应及时加注润滑油。润滑油必须进入滚子和内套的配合间隙，以改善工作条件，减少磨损。

F. the chain plate conveyer on the chain in the work should be timely filling lubricating oil. Lubricating oil must be into the roller and the inner sleeve fit clearance, in order to improve working conditions, reduce wear and tear.

以上就是对链板式输送机进行保养的方法，希望可以帮到大家，谢谢观看！

The above is the way to maintain the chain plate conveyer, the hope can help you, thanks for watching!

网址：http://www.rzhnjx.com/